
如果你无法利用它的传送能力,那将 chorus(紫颂花)变成 purpur(紫珀块)的意义何在?
关于
通过红石为 Purpur Block 提供动力,你可以创建在这些平台之间传送你的电梯平台。
该模组支持几种不同的模式;
被动(默认)
被动模式是最简单的模式,你只需要用红石永久激活 Purpur Block,
它就会在跳跃时向上传送,在潜行时向下传送。
朴素供电
朴素供电在接收到红石信号时被激活。一旦通电,它会将位于其上方的所有实体传送到最近的平台。
向上优先于向下,因此如果上下都有平台,它会把你传送到上方。
强度供电
强度供电类似于朴素供电,但它使用红石信号的强度来决定传送到哪个平台。
根据红石信号的强度,它会传送到从当前位置能到达的第 n 个平台。
信号强度为 1 时将传送到最低的平台,信号强度为 15 时将传送到第 15 个平台。
扩展
可以在平台之间放置末影棒以延长电梯的范围。
这可以在配置文件中禁用
配置
该模组本身不会生成配置文件。
要更改设置,你可以安装 Fzzy Config。
要加载对配置文件的更改,你可以使用原版的 /reload 命令。
# 电梯运行的模式。模式:('PASSIVE', 'NAIVE', 'STRENGTH')。
mode = "PASSIVE"
# 两个电梯平台之间的最大距离。
maxElevatorDistance = 16
# 使用电梯平台后,在此期间无法使用另一个平台的冷却时间(秒)。
elevatorCooldownSeconds = 0.05
# 玩家疾跑时电梯是否应工作。
activateWhileSprinting = false
# 骑乘载具的玩家是否应被电梯传送。例如矿车和船。
allowVehicles = true
# 骑乘坐骑的玩家是否应被电梯传送。例如马和猪。
allowMounts = true
# 是否允许使用末影棒来扩展电梯的范围
enableExtensions = true

What is the point of turning Chorus into Purpur if you can't use its teleporting abilities?
About
By powering Purpur Blocks using redstone, you can create elevator platforms that teleport you in between them.
The mod supports a few different modes;
Passive (default)
Passive is the simplest mode, all you need to do is permanently power the Purpur Block with redstone,
and it will teleport up by jumping, and down by crouching.
Naïve power
Naïve power activates on being powered by redstone. The moment it gets powered it will teleport all entities on top of it to the nearest platform.
Going up takes priority over going down, so if there are platforms both above and below, it will teleport you up.
Strength power
Strength power is similar to naïve power, but it uses the strength of the redstone signal to determine which platform to teleport to.
Depending on the strength of the redstone signal, it will teleport to the nth platform it can reach from there.
A signal strength of 1 will teleport to the lowest platform, and a signal strength of 15 will teleport to the 15th platform.
Extensions
End rods can be placed in-between platforms to extend the range of the elevators.
This can be disabled in the config
Configuration
On its own, the mod will not create a config file.
To change settings, you can install Fzzy Config.
To load changes to the config file, you can use the vanilla /reload command.
# The mode in which the elevator operates. Modes: ('PASSIVE', 'NAIVE', 'STRENGTH').
mode = "PASSIVE"
# The maximum distance between two elevator platforms.
maxElevatorDistance = 16
# The cooldown in seconds after using an elevator platform during which you can't use another one.
elevatorCooldownSeconds = 0.05
# Whether an elevator should work while the player is sprinting.
activateWhileSprinting = false
# Whether players riding vehicles should be teleported by the elevator. e.g minecarts and boats
allowVehicles = true
# Whether players riding mounts should be teleported by the elevator. e.g horses and pigs
allowMounts = true
# Whether the range of elevators should be able to be extended using End Rods
enableExtensions = true
评论 0
登录后参与评分
还没有评论,来抢沙发吧